| CNS Systems, Inc. |
For additional information, contact info@cnssys.com or call (410) 987-7835 |
|||
| Ordering:
Payment can be made by Credit Card (Visa, MasterCard or American Express), Wire Transfer or Checks drawn from US Banks. Purchase orders will be accepted from approved organizations. International orders must be paid in full before the products are shipped. All prices are in U.S. dollars (USD). Note: For wire transfers add $25.00 US to cover our additional processing costs. |
|
|
 |
| . |
CNS Clock II |
|
| CNSC02-A | CNS Clock II with Tac32Plus software for Win98/NT/2000/XP, power supply module, and documentation (on CD-ROM). | $1,400.00 |
| CNSC02-01 | CNS Clock II Option: High Performance PPS; Hardware Sawtooth Correction | $ 250.00 |
| CNSC02-02 | CNS Clock II Option: IRIG-B | $ 250.00 |
| CNSC02-03 | CNS Clock II Option: Sequencer Module | $ 250.00 |
| CNSC02-04 | CNS Clock II Option: Genisys Module | $ 250.00 |
| CNSC02-05 | CNS Clock II Option: RS-485 RFID Timecode Module | $ 250.00 |
| CNSC02-06 | CNS Clock II Option: Ethernet with NTP | $ 250.00 |
| CNSC02-07 | CNS Clock II Option: Steered TCXO with 10MHz output (2.5 ppm before steering). Prerequisite CNSC02-01 High Performance PPS, not available separately. | $ 250.00 |
| CNSC02-08 | CNS Clock II Option: Steered OCXO with 10MHz output (0.02ppm before steering). Prerequisite CNSC02-01 High Performance PPS, not available separately. | $ 700.00 |
| CNSC02-09 | CNS Clock II Option: Enhanced Holdover Mode Configuration. Requires option CNSC02-07 or CNSC02-08. Cannot be used with options CNSC02-02, CNSC02-03, CNSC02-04 or CNSC02-05. | $ 250.00 |
| CNSC02-10 | CNS Clock II Option: Event Recorder Interface. This option implements a specialized pulse train output on the option port, controlled by an ASCII serial message protocol. | $ 250.00 |
| CNSR01 | Rack Mount Kit for CNS Clock II (Must be ordered with CNSC02. Call for retrofit information.) | $ 45.00 |
| CNSR02 | Dial Rack Mount Kit for CNS Clock II (Must be ordered with a pair of CNSC02s. Call for retrofit information.) | $ 48.00 |
| Custom configurations are available - please call for information. | ||
| . |
|
.
|
| Tac32 | Tac32 Software | $ 89.00 |
| Tac32Plus | Tac32Plus Software | $ 250.00 |
| . | Note: Software pricing is based on Internet distribution of original software package, updates, and documentation. |
.
|
| . | Quantity discounts available starting at 10 licenses per order - please call. |
.
|
| . |
|
.
|
| T3000N | Timing 3000 Antenna, +25db gain, Double Filter, N-Connector. Includes right angle mounting bracket with U-bolt clamps. Includes TNC(F) to N(M) adaptor. The Timing 3000 is a 100% form, fit, function replacement for the original now discontinued Motorola Timing 2000 GPS Antenna. | $ 110.00 |
| AMNT2 | Adaptor, Antenna Mount, Converts M28x1 to 1.0 in. I.D. w/setscrew, for use with T2000N and T3000N. |
$ 18.00
|
| TNCN | TNC(F) to N(M) Adapter - Required to connect Coax Lxx to T2000N and T3000N antennas. This item is now included with the T2000N and T3000N antennas. |
$
8.00
|
| VIC100TNC | VIC-100 GPS ANT, +30db gain, Triple filter, TNC connector, Marine Mount. (see also AMNT1, below) | $ 120.00 |
| VIC100NMNT | VIC-100 GPS ANT, +30db gain, Triple filter, N connector and Pipe Clamp Mount (see also TNCN, below). | $ 153.00 |
| TNCN | TNC(F) to N(M) Adapter - Required to connect Coax Lxx to VIC100NMNT or T2000N antennas. | $ 8.00 |
| TNCTNC | TNC(F) to TNC(F) Adapter - Used to splice two pieces of Coax Lxx. | $ 8.00 |
| AMNT1 | Adaptor, Antenna Mount, 1" marine thread to 1" bare pipe (uses set screw), aluminum, for use with VIC100TNC. | $ 15.00 |
| AR-10S | AR-10S GPS Antenna, 28 dB active patch, 2.5-5.5 VDC @ 12 ma, magnetic mount with 5 meter coax cable and BNC connector. Also, see BNCTNC below. | $ 49.00 |
| AR-10S-DM | AR-10S-DM GPS Antenna, 28 dB active patch, 2.5-5.5 DC @ 12 ma, magnetic mount with 5 meter coax cable and BNC connector. Includes the direct mount kit with screws. Also, see BNCTNC below. | $ 53.00 |
| BNCTNC | BNC(F) to TNC(M) Adapter - Required to connect AR-10S or AR-10S-DM to the CNS Clock. | $ 8.00 |
| . |
|
.
|
| . | Standard Low Loss Coax Cable - Loss at GPS L1 frequency is approximately 9db/100ft. Outer diameter .240", micro-cell foam dielectric and type IIIA non-contaminating jacket. Nominal impedance 50 Ohms. Shield is 100% Al mylar & 95% tinned Cu braid. | . |
| CoaxL25 | Coax Cable, 25 feet, LMR240 with TNC connectors | $ 45.00 |
| CoaxL50 | Coax Cable, 50 feet, LMR240 with TNC connectors | $ 63.00 |
| CoaxL75 | Coax Cable, 75 feet, LMR240 with TNC connectors | $ 82.50 |
| CoaxL100 | Coax Cable, 100 feet, LMR240 with TNC connectors | $ 102.00 |
| CoaxL150 | Coax Cable, 150 feet, LMR240 with TNC connectors | $ 141.00 |
| CoaxL200 | Coax Cable, 200 feet, LMR240 with TNC connectors | $ 180.00 |
| . | Fire Retardant Coax Cable - same as above but has non-halogen jacket, listed CMR/MPR (PCC-FT4). |
.
|
| CoaxL50FR | Coax Cable, 50 feet, LMR240FR with TNC connectors | $ 99.00 |
| CoaxL75FR | Coax Cable, 75 feet, LMR240FR with TNC connectors | $ 136.50 |
| CoaxL100FR | Coax Cable, 100 feet, LMR240FR with TNC connectors | $ 174.00 |
| CoaxL150FR | Coax Cable, 150 feet, LMR240FR with TNC connectors | $ 249.00 |
| CoaxL200FR | Coax Cable, 200 feet, LMR240FR with TNC connectors | $ 324.00 |
| . | Extra Low Loss Coax Cable - Loss at GPS L1 frequency is approximately 5db/100ft. Outer diameter .405", micro-cell foam dielectric and type IIIA polyethylene jacket. Nominal impedance 50 Ohms. Shield is 100% Al mylar/95% tinned Cu braid. |
.
|
| CoaxM100 | Coax Cable, 100 feet, LMR400 with N connectors |
$ 150.00
|
| CoaxM100 | Coax Cable, 175 feet, LMR400 with N connectors |
$ 231.00
|
| CoaxM200 | Coax Cable, 200 feet, LMR400 with N connectors |
$ 258.00
|
| CoaxM250 | Coax Cable, 250 feet, LMR400 with N connectors |
$ 312.00
|
| CoaxM300 | Coax Cable, 300 feet, LMR400 with N connectors |
$ 366.00
|
| CoaxM400 | Coax Cable, 400 feet, LMR400 with N connectors |
$ 474.00
|
| . | Adapter Cables. These cables provide an appropriate interface between the CNS Clock and large low-loss cables, signal splitters, etc. |
.
|
| CoaxL03NFTM | Adapter cable, 3 feet, LMR240, TNC (male) connector on one end, N (female) connector on the other. This adapter cable is required to connect any CoaxMxx (LMR400) cable to the CNS Clock. It is also recommended to connect any CoaxMxx to the VIC100TNC. It is NOT required to connect a CoaxMxx to the VIC100N or VIC100NMNT. |
$ 29.95
|
| CoaxL03NMTM | Adapter cable, 3 feet, LMR240, TNC (male) connector on one end, N (male) connector on the other. This adapter cable is used connect the CNS Clock to signal amplifiers, splitters and other common signal terminating and distribution devices. |
$ 25.95
|
| CoaxX03NFTM | Flex Adapter cable, Same as CoaxL03NFTM above except uses RG-8X coaxial cable. This cable is recommended for Lab use where the convenience of a more flexible cable is necessary. |
$ 29.95
|
| CoaxX03NMTM | Flex Adapter cable, Same as CoaxL03NMTM above except uses RG-8X coaxial cable. This cable is recommended for Lab use where the convenience of a more flexible cable is necessary. |
$ 25.95
|
| . |
Out of Stock - See CNS Clock II, above. Options, upgrades and repairs are still available. |
. |
| CNSC01 | CNS Clock with Tac32 software for Windows 95/98/ME and NT4/2000/XP, power supply module and documentation (on CD-ROM, see below). Out of stock. See CNSC02 below. |
$ 789.00
|
| CNSC01-P | CNS Clock with Tac32Plus software for Windows 95/98/ME and NT4/2000/XP, power supply module and documentation (on CD-ROM, see below). | $ 950.00 |
| CNSC01-M | CNS Clock with Tac32Multi software for Windows 95/98/ME and NT4/2000/XP, power supply module and documentation (on CD-ROM, see below). | $1,050.00 |
| CNSC01-R | CNS Clock with IRIG-B Interface module, Tac32 software for Windows 95/98/ME and NT4/2000/XP, power supply module and documentation (on CD-ROM, see below). | $1,039.00 |
| CNSC01-RP | CNS Clock with IRIG-B Interface module, Tac32Plus software for Windows 95/98/ME and NT4/2000/XP, power supply module and documentation (on CD-ROM, see below). |
$1,200.00
|
| CNSC01-RM | CNS Clock with IRIG-B Interface module, Tac32Multi software for Windows 95/98/ME and NT4/2000/XP, power supply module and documentation (on CD-ROM, see below). | $1,300.00 |
| CNSC01-S | CNS Clock with Sequencer Module, Tac32 software for Windows 95/98/ME and NT4/2000/XP, power supply module and documentation (on CD-ROM, see below). | $1,039.00 |
| CNSC01-SP | CNS Clock with Sequencer Module, Tac32Plus software for Windows 95/98/ME and NT4/2000/XP, power supply module and documentation (on CD-ROM, see below). |
$1,200.00
|
| CNSC01-SM | CNS Clock with Sequencer Module, Tac32Multi software for Windows 95/98/ME and NT4/2000/XP, power supply module and documentation (on CD-ROM, see below). | $1,300.00 |
| CNSR03 | Rack Mount Kit for CNS Clock (Must be ordered with CNSC01. Call for retrofit information.) | $ 45.00 |
| . | NOTICE: CNS Clocks are now equipped with the latest Motorola M12+ precision timing receiverwith version 2.0 or newer firmware. Users with specific needs may want the Oncore VP or UT+, which was standard in earlier versions of the CNS Clock. CNS Systems has a limited quantity of Oncores in stock and will provide them as an option until supplies are exhausted. Please call if you have any questions. | . |
| . | Custom configurations are available - please call for information. |
.
|
| . |
|
.
|
| . | CNS Systems provides a wide range of consulting services for both research and development projects. This includes system, hardware and software design, implementation and analysis in the areas of communication, surveillance and navigation systems. Rates are based on the personal services of CNS Systems President Richard M. Hambly (BS, MEng Cornell University). Call for more information. | 120.00/hr |
Note: Add 6% Sales Tax if in the state of Maryland.
Prices are subject to change without notice. Quotes provided on request.
Shipping and Handling will be FOB Severna Park MD. Shipping will be by FedEx Economy unless specified otherwise.
International orders will need to contact CNS Systems to get export information and a quote on shipping to your country.
Special Orders: The CNS Clock; is highly configurable so special purpose versions can be constructed to meet a customer's particular needs. Likewise, the Tac32 software family can be specially configured to meet specific customer requirements. Call for more information.
Information and Orders:
Send purchase orders and payments to CNS Systems, Inc., Order Processing,
363 Hawick Court, Severna Park, MD 21146-1409. For credit card orders call
(410) 987-7835.
